ARRMA 1/5 Compatible 30T M1.5 Spur Gear MAKX030TS upgrade for Kraton Outcast by GPM  [MAKX030TS]

Price:
AUD$24.09
Brand:
GPM
Model:
MAKX030TS
GTIN:
4894538416794
Condition:
Brand New
Write a review

MAKX030TS spur gear: specification and fit

This MAKX030TS spur gear is an aftermarket replacement intended for ARRMA 1/5 Kraton and Outcast platforms. It is a 30-tooth spur with M1.5 module, produced in 20CrMnTi steel to provide enhanced wear resistance and bending strength versus factory materials.

Designed to handle demands from high-output 8S BLX brushless setups, the gear supports heavy-load running where consistent tooth engagement matters. Proper installation requires confirming the M1.5 module, adjusting pinion/spur mesh and shims, and replacing the listed factory references as applicable.

Packing includes

  • Spur Gear 30T Mod 1.5 - 1pcs

Original Name / Part No:

ARA310920?ARA311051

Compatible Models

  • ARRMA 1/5 Kraton 4X4 8S BLX Brushless Speed Monster Truck RTR-ARA110002 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 4WD 8S BLX Stunt Truck RTR-ARA5810 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Kraton 8S EXB 4X4 Roller Brushless Speed Truck-ARA5208 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Kraton 4X4 8S BLX EXB Brushless Monster Truck RTR-ARA5808V2 (Original Spur Gear 47T/M1.0)
  • ARRMA 1/5 Outcast 8S EXB 4X4 Roller Brushless Stunt Truck-ARA5210 (Original Spur Gear 39T/M1.0 & 47T/M1.0)
  • ARRMA 1/5 Outcast 4X4 8S BLX EXB Brushless Stunt Truck RTR-ARA5810V2 (Original Spur Gear 47T/M1.0)

Select this 20CrMnTi 30T M1.5 spur when you need a more robust aftermarket gear; verify module and mesh at installation and run a short break-in sequence to confirm alignment.

Is the MAKX030TS material hardened steel?

The gear is supplied in 20CrMnTi steel, selected for improved toughness and wear resistance suitable for higher-stress RC drivetrains.

Will this mesh with my current pinion gear?

Only if your pinion uses M1.5 module. If your original spur is M1.0, you will need a matching M1.5 pinion or a compatible drivetrain conversion.

Does it cover the listed ARRMA part numbers?

This aftermarket part is intended to replace the factory references shown in the original name block; always check the original part numbers before ordering.

Should I change bearings when fitting this gear?

Inspect bearings for wear and replace if doubtful; stronger gears transfer more load to bearings and supporting components, so fresh bearings improve long-term reliability.

Can this handle sustained stunt runs?

Yes, the material and design aim to withstand high-stress use, but overall drivetrain condition and thermal management remain important for sustained stunt driving.

Are any extra components included?

Only the spur gear itself is included in the packing list. Use existing mounting screws and shims unless extras are specified separately.

Copyright © 2008-2026 rcjaz.com.au All rights reserved