AXIAL SCX10 II Centre Shaft Steel and Aluminium Upgrade SSCX27037 by GPM  [SSCX27037]

AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037
Price:
AUD$48.52
Brand:
GPM
Model:
SSCX27037
GTIN:
4894538259070
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"

Upgraded centre shafts for SCX10 II

The SSCX27037 centre shaft set is an RC-scale replacement intended for use with AXIAL Racing SCX10 II vehicles. The design places steel in high-wear zones and uses aluminium on sections where reduced mass improves rotational behaviour.

By lowering rotating mass the driveline demands less torque during tight, technical crawling which can reduce battery load and smooth power delivery while the rig articulates. The kit aims to be compatible with SCX10 II geometry and to install with common tools.

The set includes small hardware for mounting: M4*2.5*11 screw shaft - 4pcs, 4*2.5 O-ring - 4pcs.

Compatible Models

  • Axial SCX-10 II AX

Use these shafts when you want a lighter centre drivetrain piece for scale crawling rigs based on the SCX10 II platform, and service the joints and seals at regular intervals.

Will I need to modify my axle housings?

Most SCX10 II housings accept these shafts without modification if your current lengths fall within S:118mm-128mm and L:130mm-140mm; always double-check measurements first.

How does this affect battery consumption?

Reducing rotating mass lowers the torque needed at low speeds, which can trim brief bursts of current draw during technical crawling, helping overall efficiency.

What maintenance should I plan?

Inspect for lateral play, keep contact points lightly lubricated with a product safe for steel and aluminium, and renew O-rings when they harden or tear.

Do I need special tools to fit the kit?

Basic hand tools and a small hex driver set are sufficient; have thread locker available for final assembly and confirm screw torque after a test run.

Copyright © 2008-2026 rcjaz.com.au All rights reserved