Kyosho Mini-Z AWD Aftermarket Rear Knuckle Holder Alloy 0.6mm, Toe Out -0.2mm MZA031R-0206 by GPM  [MZA031R-0206]

Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206
Price:
AUD$6.68
Brand:
GPM
Model:
MZA031R-0206
GTIN:
4894538121902
Condition:
Brand New
Write a review
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"

Aftermarket alloy rear knuckle holder for Mini-Z AWD

This alloy rear knuckle arm holder is supplied for Kyosho Mini-Z AWD rear assemblies as a single replacement item. It fixes the rear toe at -0.2mm and features a 0.6mm plate to provide a modest, repeatable change to rear geometry for handling tweaks.

Designed for direct swap-in or as an upgrade, the alloy component aims to keep geometry stable under normal running conditions. Confirm the part matches your Mini-Z AWD variant before fitting and ensure the toe value fits your setup plan.

Installation advice: check alignment of the holder before tightening, use correct mounting hardware, and verify wheel and suspension clearance through the full range of motion. Supplied as 1 pcs.

Can this replace OEM rear knuckle plates?

Yes, it is intended as a replacement option, but you should check the mounting pattern and thickness against the OEM part to ensure a correct fit.

Will the thickness affect suspension travel?

At 0.6mm, the plate provides a small increase in stiffness with minimal impact on suspension motion; always cycle the suspension to confirm there is no interference.

What comes in the box?

The package contains a single alloy knuckle arm holder, noted as 1 pcs in the product details.

Copyright © 2008-2026 rcjaz.com.au All rights reserved