TRAXXAS 1/18 Latrax Rally Aluminium Knuckle Arm LTX021 by GPM  [LTX021]

TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021
Price:
AUD$22.76
Brand:
GPM
Model:
LTX021
GTIN:
4894538090154
Condition:
Brand New
Write a review
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"
alt="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021" title="TRAXXAS 1/18 Latrax Rally Aluminium Front Knuckle Arm - 1pr set - GPM LTX021"

Upgrade knuckle arm for Latrax Rally 1/18

This aluminium front knuckle arm is an RC-scale steering component intended for the TRAXXAS 1/18 Latrax Rally chassis. It replaces the original plastic knuckle arm to provide a stiffer mounting surface for steering linkages and the suspension upright while retaining scale-compatible fit.

Fitting is straightforward: remove the stock knuckle, line up the aluminium arm with the upright and steering linkage, then secure using the existing fasteners. Use the recommended torque settings and confirm that steering and suspension retain full free movement after installation.

An aluminium option reduces component flex versus plastic, which can sharpen steering response and make small setup changes behave more predictably. After fitting, check wheel toe and camber and inspect fastener interfaces for loosening or wear.

Specifications

  • Item: Front knuckle arm, 1pr set
  • Material: Aluminium
  • Model Number: GPM LTX021
  • Compatibility: TRAXXAS 1/18 Latrax Rally

A no-nonsense aluminium replacement for the Latrax Rally front knuckle that focuses on consistent steering feel and longer service life for hobby use.

Does this require any chassis modification?

No chassis modification is normally required. The arm is made to match the stock mounting points for the Latrax Rally 1/18.

Should I swap other parts at the same time?

Consider checking ball studs and bearings; replacing worn items while you install the knuckle arm is an efficient tune-up step.

How often should I inspect the aluminium arm?

Inspect mounting screws and mating surfaces after the first few runs and then as part of regular maintenance, especially if you run off-road or on abrasive surfaces.

Will this change ground clearance?

The part is a like-for-like replacement in terms of geometry, so ground clearance should remain unchanged when fitted correctly.

Copyright © 2008-2026 rcjaz.com.au All rights reserved