TRAXXAS SLASH 4X4 Upgrade Low-CG Aluminium Main Shaft SLA025LCG by GPM  [SLA025LCG]

TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG
Price:
AUD$28.48
Brand:
GPM
Model:
SLA025LCG
GTIN:
4894538078329
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"
alt="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG" title="TRAXXAS SLASH 4X4 LOW-CG Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM SLA025LCG"

Low-CG aluminium main shaft designed for Slash 4X4

This aftermarket main shaft is supplied as one piece for use with TRAXXAS SLASH 4X4 drivetrains. It combines an aluminium shaft body with hardened steel end fittings to limit rotating mass while keeping the wear surfaces strong.

Fitting is straightforward for anyone used to Slash 4X4 service: remove the original shaft, inspect splines and bearings, then fit the replacement using the original retaining screws. No specialist tooling is normally required.

In practical tuning terms the low-CG design helps concentrate less mass at the outer ends and the steel fittings preserve spline life, which can result in smoother power transfer and reduced service frequency for off-road running and club events.

Specifications

  • Item Main Shaft
  • Material Aluminium body with hard steel ends
  • Model Number SLA025LCG
  • Compatibility TRAXXAS SLASH 4X4
  • Quantity 1 pcs

This shaft is intended as a direct replacement where reducing rotating mass and reinforcing bearing interfaces is desired; always confirm spline and retention compatibility before installation.

Is the SLA025LCG compatible with all Slash 4X4 setups?

Compatibility depends on spline type and retention method used on your vehicle. Compare these features to your stock shaft to confirm a match.

Will changing to this shaft affect gearing?

The shaft does not alter gear ratios. Changes in driveline feel come from reduced rotating inertia rather than different gearing.

Any tips for long life?

Keep splines clean, avoid grit ingress, replace bearings when show signs of wear, and use light corrosion protection on steel ends after wet runs.

Copyright © 2008-2026 rcjaz.com.au All rights reserved