TRAXXAS Xo-1 Alloy Wheel Hex Claw 0mm XO006 by GPM  [XO006]

TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006
Price:
AUD$34.21
Brand:
GPM
Model:
XO006
GTIN:
4894538035292
Condition:
Brand New
2 Reviews
Write a review
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"

Alloy 0mm wheel hex claw for Xo-1

The XO006 aluminium wheel hex claw is a precision aftermarket part created to mate with TRAXXAS Xo-1 wheel hubs. Supplied as a matched pair, these alloy hex claws keep the original 0mm offset and provide a secure mounting interface for standard Xo-1 wheel assemblies.

Installation follows conventional hub service steps: remove wheel and original hex, inspect bearing fit and hub face, then press or fasten the aluminium claw in the hub using the correct hardware orientation. Tighten to proper torque and inspect for runout to ensure alignment.

For setup and repairs this component replaces worn hexes and helps retain accurate wheel geometry. The aluminium build maintains consistent mounting surfaces useful for dialling in toe, camber, and wheel balance during setup sessions.

Specifications

  • Item Aluminium Wheel Hex Claw (0mm) - 2 pcs
  • Material Aluminium
  • Model Number XO006
  • Compatibility TRAXXAS Xo-1

XO006 is recommended where a durable 0mm aluminium hex is required for TRAXXAS Xo-1 wheel mounting; confirm hub compatibility before use.

 

Product Reviews
2 Reviews
rating
Just finished building a 4-tec 2.0 with GPM parts. SOOO beautiful. After having a bad experience building a wltoys this summer it was nice to once again do another build using GPM parts. The website is nothing to brag about but, the parts are top quality.
rating
Once again it was a pleasure dealing with GPM customer service to inquire about a part. GPM was able to fill my order in a timely manner. Excellent communication from customer service. Thanks GPM!

Do these work with aftermarket wheels?

They are designed for Xo-1 hubs; compatibility with wheels depends on wheel inner bore and mounting design.

Is there a recommended torque?

Use the hub manufacturers recommended screw torque for hex fasteners and verify after a short run.

Can these be reused after removal?

If the hex claw shows no deformation or burrs it can be reused, otherwise replace to maintain geometry.

What is included in the pack?

Two aluminium wheel hex claws are included, enough for one axle set on a vehicle.

Copyright © 2008-2026 rcjaz.com.au All rights reserved