TRX4 Bevel Gear 34T with 11T Pinion 40CR Steel Aftermarket Replacement TRX41134T by GPM  [TRX41134T]

TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 34T & Pinion Gear 11T - GPM TRX41134T
Price:
AUD$30.49
Brand:
GPM
Model:
TRX41134T
GTIN:
4894538380378
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 34T & Pinion Gear 11T - GPM TRX41134T" title="TRAXXAS TRX4 TRAIL CRAWLER 40CR Steel Differential Bevel Gear 34T & Pinion Gear 11T - GPM TRX41134T"

Aftermarket bevel and pinion for TRX4 gearboxes

This replacement kit supplies the internal differential bevel and matching pinion used in TRX4-based trail crawlers. It contains a 34T bevel differential gear and an 11T pinion produced from 40CR steel for scale RC drivetrain use only.

The components sit in the inner front or rear gearbox where they transmit torque from the motor to each axle. These aftermarket gears are intended to restore correct tooth engagement and consistent power transfer for off-road crawling rigs.

Fitment advice: set the correct gear mesh and backlash using your existing spur and pinion before final assembly, remove any contaminants from inside the gearbox, and coat mating teeth with a suitable RC gear grease to reduce friction and wear.

Packing includes

  • Diff bevel gear - 1pcs
  • Pinion gear - 1pcs

Original Name / Part No:

8279?8279R

Compatible Models

  • TRAXXAS-1/10 ELECTRIC 4WD TRX4 DEFENDER TRAIL CRAWLER -82056-4
  • TRAXXAS-1/10 ELECTRIC 4WD TRX4 FORD BRONCO TRAIL CRAWLER-82046-4
  • TRAXXAS-1/10 4WD ELECTRIC TRX-4 BLAZER -82076-4
  • TRAXXAS-1/10 AND TRX-4 1972 CHEVROLET K5 BLAZER TRAIL CRAWLER-92086-4
  • TRAXXAS-1/10 AND TRX-4 CHEVROLET K10 TRAIL CRAWLER-92056-4
  • TRAXXAS-1/10 AND TRX-4 CRAWLER EQUIPPED WITH TRAXX-82034-4
  • TRAXXAS-1/10 AND TRX-4 FORD BRONCO TRAIL CRAWLER-92076-4
  • TRAXXAS-1/10 AND TRX-4 FORD F-150 RANGER XLT TRAIL CRAWLER-92046-4
  • TRAXXAS-1/10 AND TRX-4 LAND ROVER DEFENDER TRAIL CRAWLER-82056-4
  • TRAXXAS-1/10 4X4 TRX-4 SPORT HIGH TRAIL EDITION-82044-4
  • TRAXXAS-1/10 TRX-4 SPORT UNASSEMBLED KIT-82010-4
  • TRAXXAS-1/10 TRX-4 SPORT-82024-4
  • TRAXXAS-1/10 TRX-4 UNASSEMBLED KIT-82016-4
  • TRAXXAS-1/10 TRX-6 MERCEDES-BENZ G 63 AMG 6X6-88096-4
  • TRAXXAS-1/10 TRX-6 ULTIMATE RC HAULER-88086-4
  • TRAXXAS-1/10 TRX-6 ULTIMATE RC HAULER-88086-84

Fit this 40CR bevel and pinion set when diff teeth wear affects engagement, restoring dependable low-speed crawling response in TRX4 and compatible TRX-6 gearboxes.

Do these gears require break-in?

Run the model gently after installation and recheck mesh; light break-in under low load helps mating surfaces seat together for quieter operation.

Will these work with upgraded axles?

They are compatible where the internal gearbox layout and tooth counts match; upgraded axles do not typically affect internal bevel fitment but verify clearances first.

Is heat treatment used?

The gears are specified as 40CR steel; confirm hardness or heat treatment details with your supplier if this is critical for high-load builds.

How often should I inspect the gears?

Inspect after heavy use or exposure to dirt and water, and re-apply grease as needed to extend service life.

Copyright © 2008-2026 rcjaz.com.au All rights reserved